| Fixed Contact | Provides a stationary electrical connection with the moving contact and carries current during normal operation. | Copper or copper alloy with a silver-based contact surface; insulated mounting support. | Contact resistance, current rating, contact geometry, surface finish, thermal stability, and compatibility with the moving contact. | Dimensional inspection, contact resistance testing, surface coating inspection, heat-rise testing, and material verification. | Contact materials must balance conductivity, wear resistance, welding resistance, and cost. | High |
| Moving Contact | Opens and closes the current path when the operating mechanism is actuated or a fault is detected. | Copper alloy, conductive arm, contact pad, spring connection, and wear-resistant contact material. | Travel distance, opening speed, closing force, alignment, contact pressure, and endurance cycle requirements. | Operating-cycle testing, contact alignment, travel measurement, contact pressure, and mechanical wear inspection. | Fast separation helps limit arcing time and improves interruption performance. | High |
| Arc Chute | Splits, cools, and extinguishes the electric arc produced when contacts separate under load or fault conditions. | Heat-resistant insulating plates, deion plates, arc runners, and molded insulating housing. | Arc chamber dimensions, plate spacing, dielectric strength, thermal resistance, and compatibility with the rated voltage and current. | Visual inspection, dimensional checks, insulation testing, arc interruption testing, and heat-resistance verification. | Its design is specific to the breaker architecture and cannot normally be substituted by appearance alone. | Critical |
| Trip Unit | Detects overloads, short circuits, or other abnormal conditions and initiates the opening operation. | Thermal element, magnetic actuator, electronic sensor, microcontroller, or a combined protection assembly. | Rated current, overload curve, instantaneous trip level, accuracy, reset behavior, auxiliary functions, and operating temperature. | Calibration testing, trip-time testing, current injection testing, temperature testing, and functional verification. | Protection settings must match the system voltage, load characteristics, conductor capacity, and coordination requirements. | Critical |
| Thermal Bimetal Element | Responds to sustained overcurrent by heating and bending to release the trip mechanism. | Bonded metals with different thermal expansion coefficients, usually formed into a calibrated strip. | Rated current, thermal response, ambient-temperature compensation, trip curve, and recovery characteristics. | Current-versus-time testing, calibration verification, dimensional checks, and temperature-cycle testing. | Trip performance changes with ambient temperature and must be evaluated across the specified operating range. | High |
| Magnetic Trip Coil | Creates a rapid magnetic force that trips the breaker during high short-circuit current. | Insulated copper winding, magnetic core, bobbin, spring, and plunger or armature. | Pickup current, response time, coil resistance, insulation class, magnetic clearance, and mechanical travel. | Coil resistance, pickup-current measurement, response-time testing, insulation testing, and endurance testing. | Fast operation is essential for limiting let-through energy during short-circuit events. | Critical |
| Operating Mechanism | Stores and transfers mechanical energy to close, hold, and open the contacts. | Springs, shafts, latches, links, cams, bearings, and metal or engineered-polymer supports. | Operating force, release time, reset force, mechanical endurance, tolerances, and compatibility with manual or motor operation. | Mechanical cycle testing, opening and closing time, latch verification, torque measurement, and wear inspection. | Mechanism tolerances directly affect contact pressure, switching reliability, and service life. | Critical |
| Latch and Release Assembly | Holds the contacts in the closed position and releases them when the trip unit or manual control commands an opening operation. | Hardened metal latch surfaces, springs, release lever, pivot points, and insulating supports. | Release force, latch stability, reset behavior, wear resistance, and compatibility with the trip actuator. | Release-force testing, repeated-operation testing, latch retention checks, and dimensional inspection. | Unintended release must be prevented while ensuring dependable operation under fault conditions. | High |
| Housing and Cover | Encloses internal components, provides insulation, protects against mechanical damage, and supports mounting features. | Flame-retardant thermoplastic or thermoset insulating material with molded inserts and barriers. | Insulation voltage, flame resistance, impact strength, dimensional stability, creepage distance, and ingress protection. | Visual and dimensional inspection, dielectric withstand testing, flame-resistance testing, impact testing, and torque checks. | Housing design must maintain required clearances and withstand heat generated during normal and fault operation. | Critical |
| Terminal and Terminal Clamp | Connects the breaker to incoming and outgoing conductors and maintains secure electrical pressure. | Tinned copper or copper alloy terminal, steel clamp, screw, and anti-loosening features. | Conductor size range, tightening torque, current capacity, resistance to loosening, plating quality, and temperature rise. | Torque testing, pull-out testing, contact-resistance measurement, heat-rise testing, and corrosion inspection. | Terminal geometry must match the conductor type, conductor size, and installation method. | Critical |
| Terminal Screw | Applies clamping force to secure the conductor or busbar to the terminal assembly. | Plated carbon steel, stainless steel, or other corrosion-resistant alloy selected for the application. | Thread size, head type, tensile strength, surface treatment, tightening torque, and resistance to stripping. | Thread-gauge inspection, torque-to-failure testing, coating inspection, hardness testing, and corrosion testing. | Incorrect screw material or torque can cause loose connections, overheating, or terminal damage. | High |
| Insulating Barrier | Separates conductive components and helps prevent phase-to-phase or phase-to-ground faults. | Flame-retardant thermoplastic, thermoset resin, molded insulation, or insulating sheet material. | Dielectric strength, creepage distance, clearance, temperature rating, dimensional accuracy, and moisture resistance. | Dielectric withstand testing, insulation-resistance testing, dimensional checks, and heat-aging evaluation. | Barrier dimensions must be maintained after molding, assembly, and thermal cycling. | Critical |
| Handle and Manual Operator | Allows the user to manually open, close, and reset the circuit breaker and indicates its operating position. | Impact-resistant insulating polymer, actuator shaft, linkage, and position indicator. | Operating force, travel angle, position visibility, grip strength, reset action, and mechanical endurance. | Cycle testing, operating-force measurement, position-indicator verification, impact testing, and dimensional inspection. | Clear ON, OFF, and TRIPPED indications reduce operating and maintenance errors. | Medium |
| Auxiliary Contact | Provides an electrical signal indicating the breaker status for control, monitoring, interlocking, or alarm circuits. | Miniature contact set, spring mechanism, insulating carrier, terminals, and housing. | Contact arrangement, rated control voltage, current rating, switching category, insulation, and electrical endurance. | Continuity testing, contact-resistance testing, switching-cycle testing, dielectric testing, and terminal inspection. | Control-circuit ratings may differ from the main power-circuit rating and must be specified separately. | Medium |
| Undervoltage Release | Trips or prevents closing of the breaker when the control voltage falls below its specified operating level. | Electromagnetic coil, plunger, spring, actuator, and insulating enclosure. | Pickup voltage, dropout voltage, response time, rated control voltage, and power consumption. | Voltage-ramp testing, trip-time testing, endurance testing, coil-resistance measurement, and insulation testing. | Control-voltage tolerances and transient behavior must be considered for the target electrical system. | High |
| Shunt Trip Release | Opens the breaker when an external electrical command is applied, such as an emergency-stop or remote-trip signal. | Electromagnetic coil, plunger, spring, actuator, and terminal assembly. | Control voltage, pulse duration, trip response time, coil power, insulation level, and duty cycle. | Voltage and pulse testing, response-time measurement, repeated-trip testing, and insulation verification. | Control wiring, polarity where applicable, and the permitted operating duty must be defined before sourcing. | High |
| Accessories and Mounting Hardware | Supports installation, connection, identification, interlocking, sealing, and integration with distribution equipment. | Metal brackets, insulating clips, rails, screws, spacers, seals, labels, and terminal accessories. | Mechanical compatibility, corrosion resistance, mounting dimensions, torque requirements, and environmental rating. | Fit and interchangeability checks, torque testing, corrosion inspection, labeling verification, and packaging inspection. | Accessory interfaces should be validated with the complete breaker assembly rather than as isolated parts. | Medium |